Plumbing, Heating & Cooling Services in Evanston, IL

Completed Spring Cooling Tune-Up on residential air conditioning system. Performed comprehensive inspection of blower wheel assembly, confirming proper blade condition and clearances with no debris accumulation or damage noted. Verified operation of REME-HALO air purification system installed in supply plenum, checked UV lamp function and mounting integrity. All components found operating within normal parameters and system ready for cooling season.

Completed comprehensive HVAC estimate for full system replacement on 15-year-old unit experiencing restricted airflow at both the filter and metering device. Assessed existing thermostat and outdoor condenser installation beneath elevated deck structure, documenting current system configuration and access requirements for future replacement work.

Responded to no cooling complaint on residential air conditioning system. Upon arrival, performed diagnostic testing using digital multimeter to check electrical components and system operation. Inspected outdoor condensing unit including compressor, contactor, and capacitor. System evaluated and determined to be operating within normal parameters during service call. Customer educated on proper system operation and maintenance requirements.

Completed comprehensive maintenance agreement service on residential heat pump system including outdoor condenser unit and indoor air handler. Performed thorough inspection of both units, verified proper operation of all components, checked refrigerant levels, cleaned condenser coils, inspected electrical connections, and tested system performance per manufacturer specifications. All equipment found operating within normal parameters with no deficiencies noted at time of service.

Responded to gas odor call back following utility company shutoff. Performed comprehensive inspection of HVAC system gas connections and piping in mechanical room. Checked all gas line connections, valves, and fittings for leaks using approved detection methods. Verified proper installation of gas supply lines to furnace unit, inspected yellow brass valve connections and copper piping runs. Confirmed all connections were secure and properly sealed. Coordinated with gas utility for system re-pressurization and final clearance to restore service.

Completed full HVAC system replacement including Carrier furnace, air conditioning unit, evaporator coil, and humidifier. Two-person crew successfully removed existing equipment and installed all new components in a single day. All ductwork connections were properly sealed and secured, electrical wiring completed to manufacturer specifications, and humidifier integrated with new furnace system. System tested and verified operational upon completion.

Completed preventive maintenance agreement service on two Carrier air conditioning systems. Performed comprehensive inspection of outdoor condensing units, verified electrical disconnect operation and connections, checked refrigerant levels, and inspected condenser coil condition. Replaced 16x25x1 air filters per agreement specifications, with 16x25x4 media filter scheduled for fall service.

Installed a new 75-gallon Bradford White residential water heater in basement utility area. Performed complete water heater replacement including all necessary copper supply line connections with brass fittings and valves, installed recirculation pump with electrical connections, and connected required PVC venting. Unit was properly positioned on concrete floor, all plumbing connections were secured and tested for leaks, and system was commissioned and verified operational.

Responded to no-cool call for rooftop unit not powering on. Upon arrival, accessed RTU using 28' ladder and performed diagnostic testing with multimeter on electrical panels. Inspected wall-mounted PRO1 thermostat in protective enclosure and verified proper settings and wiring connections, documenting equipment condition with photos for service records.

Completed installation of single-zone ductless mini-split air conditioning system at residential property. Mounted outdoor condensing unit on concrete pad at exterior foundation with proper clearances, ran insulated refrigerant line sets along base of structure, and installed indoor wall-mounted air handler unit in upper room with vaulted ceiling. System was properly commissioned, tested for proper operation, and left in full working condition.

Performed backflow assembly test on residential property as requested. Inspected plumbing system and water heater installation in basement utility area. Documented equipment condition including Smith brand water heater, copper supply lines, pressure relief valve, gas control assembly, and associated plumbing connections. All components photographed for service records. Testing completed with no emergency issues identified.

Provided estimate for complete HVAC system replacement including outdoor condensing unit and indoor furnace. Current 10-year-old air conditioning unit located in backyard between house and fence is low on refrigerant due to consistent leaks, making replacement more cost-effective than repair. Customer requested quote for relocating outdoor unit to improved location with better clearance from vegetation and structures. Assessed existing Lennox furnace system in basement and outdoor condensing unit positioned on concrete pad with inadequate clearance from overgrown vegetation. Recommended replacement of both outdoor and indoor equipment to ensure proper system matching, efficiency, and warranty coverage. Discussed optimal placement options for new condensing unit to provide adequate service clearance and airflow while addressing customer's relocation preference.

Replaced two existing electrical disconnect boxes on exterior wall with new units and installed two surge protectors to provide equipment protection. All electrical connections were properly secured, conduit runs completed, and system tested for proper operation.

Completed cooling cycle maintenance and general service inspection on air conditioning system. Verified thermostat operation showing proper temperature control and system response, checked electrical components and connections using diagnostic testing equipment, and inspected HVAC unit accessibility and ductwork. Filter size 16x25x4 was noted as not included in this service agreement.

Completed comprehensive air conditioning maintenance agreement inspection on outdoor condenser unit and indoor components. Performed thorough evaluation of condenser coil for cleanliness and visible leaks, inspected blower motor and wheel for debris accumulation, and measured indoor relative humidity levels. Tested refrigerant charge levels, cycled and inspected all operating controls for proper function, and examined line voltage switches and electrical wiring connections for tightness and deterioration. Verified condensate drainage system operation, inspected refrigerant lines for visible leaks and insulation integrity, and confirmed all safety and performance parameters met manufacturer specifications. System operating normally with thermostat displaying proper temperature control and humidity readings.

Completed annual maintenance agreement service on air conditioning system and air handler. Inspected evaporator coil and condenser units, verified refrigerant lines and electrical connections, and documented equipment condition with photos. Customer advised that 20x25x5 filter is not included in agreement coverage and must be provided separately. Annual maintenance agreement renewed for continued service coverage.

Completed leak repair on the suction line located at the outdoor condenser unit. Replaced two defective Schrader valves to restore proper refrigerant service port functionality and system integrity. Installed a new capacitor to ensure reliable compressor and fan motor operation. Applied insulation to the suction line to prevent condensation, improve system efficiency, and protect against refrigerant line sweating. All refrigerant connections were properly sealed and tested for leaks. System was evaluated for proper operation following repairs.

Completed full air conditioning system replacement including evaporator coil installation on existing Lennox furnace in residential basement mechanical room. Removed old A/C unit and coil, installed new evaporator coil assembly atop furnace, connected refrigerant lines, and integrated condensate drainage system with existing white PVC piping. Verified all electrical connections, secured wiring with proper cable management, completed ductwork connections to ensure proper airflow distribution, and tested system operation to confirm cooling functionality. Installation completed by two-person crew in half-day timeframe.

Performed comprehensive maintenance on two air conditioning systems as part of preventive maintenance agreement. Replaced air filters with 16x20x1 and 16x25x1 filters, inspected blower wheel assembly for proper operation and cleanliness, and conducted general service inspection of outdoor condenser units to ensure optimal system performance.

Responded to emergency call for tanked water heater failure resulting in complete loss of hot water. Upon arrival, found water heater in severely deteriorated condition with extensive water damage to surrounding floor area and visible corrosion staining throughout the installation space. Unit exhibited signs of catastrophic failure with significant moisture intrusion and long-term neglect. Documented existing conditions through photographic evidence showing rust-colored staining patterns on floor surface, damaged equipment housing, and compromised internal components. Assessed water heater system and confirmed unit was beyond repair, requiring full replacement. Provided customer with emergency service during evening hours to address immediate hot water restoration needs.